Gas metal arc welding

To perform gas metal arc welding, the basic necessary equipment is a welding gun, a wire feed unit, a welding power supply, an electrode wire, and a shielding gas supply.

Most applications of gas metal arc welding use a constant voltage power supply
Alternating current is rarely used with GMAW; instead, direct current is employed and the electrode is generally positively charged(DCEP)

Electrode
The selection of electrode depends on the process variation being used, the composition of the metal being welded, the joint design, and the material surface conditions.
All electrode contain deoxidizing metals such as silicon, manganese, titanium, and aluminum in small percentages to help prevent oxygen porosity, and some contain denitriding metals such as titanium and zirconium to avoid nitrogen porosity.[9]
The diameters of the electrodes used in GMAW typically range from 0.7 to 2.4 mm (0.028–0.095 in), but can be as large as 4 mm (0.16 in). The smallest electrodes are associated with short-circuiting metal transfer, while the pulsed spray mode generally uses electrodes of at least 1.6 mm (0.06 in).[10]

Shielding gas
Shielding gases are necessary for gas metal arc welding to protect the welding area from atmospheric gases such as nitrogen and oxygen, which can cause fusion defects, porosity, and weld metal embrittlement if they come in contact with the electrode, the arc, or the welding metal. This problem is common to all arc welding processes, but instead of a shielding gas, many arc welding methods utilize a flux material which disintegrates into a protective gas when heated to welding temperatures. In GMAW, however, the electrode wire does not have a flux coating, and a separate shielding gas is employed to protect the weld. This eliminates slag, the hard residue from the flux that builds up after welding and must be chipped off to reveal the completed weld.
The choice of a shielding gas depends on several factors, most importantly the type of material being welded and the process variation being used. Pure inert gases such as argon and helium are only used for nonferrous welding; with steel they cause an erratic arc and encourage spatter (with helium) or do not provide adequate weld penetration (argon). Pure carbon dioxide, on the other hand, allows for deep penetration welds but encourages oxide formation, which adversely affect the mechanical properties of the weld. Its low cost makes it an attractive choice, but because of the violence of the arc, spatter is unavoidable and welding thin materials is difficult. As a result, argon and carbon dioxide are frequently mixed in a 75%/25% or 80%/20% mixture, which reduces spatter and makes it possible to weld thin steel workpieces.
Argon is also commonly mixed with other gases, such as oxygen, helium, hydrogen, and nitrogen. The addition of up to 5% oxygen encourages spray transfer, which is critical for spray-arc and pulsed spray-arc GMAW. However, more oxygen makes the shielding gas oxidize the electrode, which can lead to porosity in the deposit if the electrode does not contain sufficient deoxidizers. An argon-helium mixture is completely inert, and is used on nonferrous materials. A helium concentration of 50%–75% raises the voltage and increases the heat in the arc, making it helpful for welding thicker workpieces. Higher percentages of helium also improve the weld quality and speed of using alternating current for the welding of aluminum. Hydrogen is added to argon in small concentrations (up to about 5%) for welding nickel and thick stainless steel workpieces. In higher concentrations (up to 25% hydrogen), it is useful for welding conductive materials such as copper. However, it should not be used on steel, aluminum or magnesium because of the risk of hydrogen porosity. Additionally, nitrogen is sometimes added to argon to a concentration of 25%–50% for welding copper, but the use of nitrogen, especially in North America, is limited. Mixtures of carbon dioxide and oxygen are similarly rarely used in North America, but are more common in Europe and Japan.
Recent advances in shielding gas mixtures use three or more gases to gain improved weld quality. A mixture of 70% argon, 28% carbon dioxide and 2% oxygen is gaining in popularity for welding steels, while other mixtures add a small amount of helium to the argon-oxygen combination, resulting in higher arc voltage and welding speed. Helium is also sometimes used as the base gas, to which smaller amounts of argon and carbon dioxide are added. Additionally, other specialized and often proprietary gas mixtures claim to offer even greater benefits for specific applications.[11]
The desirable rate of gas flow depends primarily on weld geometry, speed, current, the type of gas, and the metal transfer mode being utilized. Welding flat surfaces requires higher flow than welding grooved materials, since the gas is dispersed more quickly. Faster welding speeds mean that more gas must be supplied to provide adequate coverage. Additionally, higher current requires greater flow, and generally, more helium is required to provide adequate coverage than argon. Perhaps most importantly, the four primary variations of GMAW have differing shielding gas flow requirements—for the small weld pools of the short circuiting and pulsed spray modes, about 10 L/min (20 ft³/h) is generally suitable, while for globular transfer, around 15 L/min (30 ft³/h) is preferred. The spray transfer variation normally requires more because of its higher heat input and thus larger weld pool; along the lines of 20–25 L/min (40–50 ft³/h).[12]

The orientation of the gun is also important—it should be held so as to bisect the angle between the work pieces; that is, at 45 degrees for a fillet weld and 90 degrees for welding a flat surface. The travel angle or lead angle is the angle of the torch with respect to the direction of travel, and it should generally remain approximately vertical. However, the desirable angle changes somewhat depending on the type of shielding gas used—with pure inert gases, the bottom of the torch is out often slightly in front of the upper section, while the opposite is true when the welding atmosphere is carbon dioxide.[14

SAFETY HAZARD S INCLUDE
Extreme heat and flame
Ultraviolet light
Particulate matter
Carbon monoxide
Ozone
GLOBULAR TRANSFER
As the weld is made, a ball of molten metal from the electrode tends to build up on the end of the electrode, often in irregular shapes with a larger diameter than the electrode itself. When the droplet finally detaches either by gravity or short circuiting, it falls to the workpiece, leaving an uneven surface and often causing spatter.
limited to flat and horizontal welding positions

tendency to produce high heat, a poor weld surface, and spatter.
uses carbon dioxide,
high deposition rate,

SHORT CIRCUIT TRANSFER
Molten droplets form on the tip of the electrode, but instead of dropping to the weld pool, they bridge the gap between the electrode and the weld pool as a result of the greater wire feed rate. This causes a short circuit and extinguishes the arc, but it is quickly reignited after the surface tension of the weld pool pulls the molten metal bead off the electrode tip.
This process is repeated about 100 times per second, making the arc appear constant to the human eye.
possible to weld thinner materials
better weld quality and less spatter than the globular variation, and it allows for welding in all positions but slower


SPRA Y TRANSFER :
Molten metal droplets (with diameters smaller than the electrode diameter) are rapidly passed along the stable electric arc from the electrode to the work piece
eliminating spatter and resulting in a high-quality weld finish.
high amounts of voltage and current are necessary
used only on workpieces of thicknesses above about 6 mm (0.25 in).
it is often limited to flat and horizontal welding position
The maximum deposition rate for spray arc GMAW is relatively high; about 60 mm/s (150 in/min).[22



PULSE TRANSFER

Based on the principles of spray transfer but uses a pulsing current to melt the filler wire and allow one small molten droplet to fall with each pulse.
The pulses allow the average current to be lower, decreasing the overall heat input and thereby decreasing the size of the weld pool and heat-affected zone while making it possible to weld thin work pieces
The smaller weld pool gives the variation greater versatility, making it possible to weld in all positions.
it requires a special power source capable of providing current pulses with a frequency between 30 and 400 pulses per second.